基于的液压夹紧的专用夹具设计支架零件说明书带图纸.doc
《基于的液压夹紧的专用夹具设计支架零件说明书带图纸.doc》由会员分享,可在线阅读,更多相关《基于的液压夹紧的专用夹具设计支架零件说明书带图纸.doc(51页珍藏版)》请在启牛文库网上搜索。
1、毕业设计说明书论文QQ1961660126编号无锡太湖学院毕业设计(论文)题目: 基于液压夹紧的专用夹具设计 支架零件的工艺工装设计 信机 系 机械工程及自动化 专业学 号: 学生姓名: 指导教师: (职称:副教授 ) (职称: )2013年5月25日课件之家的资料精心整理好资料-本资料来自无锡太湖学院本科毕业设计(论文)诚 信 承 诺 书本人郑重声明:所呈交的毕业设计(论文) 基于液压夹紧的专用夹具设计 是本人在导师的指导下独立进行研究所取得的成果,其内容除了在毕业设计(论文)中特别加以标注引用,表示致谢的内容外,本毕业设计(论文)不包含任何其他个人、集体已发表或撰写的成果作品。 班 级:
2、机械97 学 号: 0923816 作者姓名: 2013 年 5 月 25 日毕业设计说明书论文QQ1961660126摘 要本文是对支架零件的加工工艺规程进行设计,并针对其中某一道工序进行基于液压的专用夹具设计,并进行了另一工序的普通夹具设计。支架零件作为叉架类零件,其主要加工表面是平面及孔。按照机械加工工艺要求,遵循先面后孔的原则,并将孔与平面的加工明确划分成粗加工和精加工阶段以保证加工精度。基准选择以支架大外圆端面作为粗基准,以支架大外圆端面与两个工艺孔作为精基准,确定了其加工的工艺路线和加工中所需要的各种工艺参数。并按要求对其中一道工序进行了基于液压夹紧的专用夹具设计,在设计中计算了此
3、道工序所受的切削力及切削力矩,进而确定了液压缸的负载,选定整个液压系统的压力,从而确定了液压缸的各参数,绘制了液压夹紧的专用夹具总图。整个加工过程均选用万能机床。关键词 支架;加工工艺;液压;专用夹具毕业设计说明书论文QQ1961660126AbstractThis article is carries on the design of the bracket components machine process, and the clamp designed based on the hydraulic pressure which aimed at some working process
4、, and has carried on another working procedure ordinary jig design. The bracket components take the boom trestle class components, its main processing surface is the plane and the hole. According to the machine-finishing technological requirement, after following the first surface, the hole principl
5、e, and is clear about the hole and the plane processing divides the rough machining and the precision work stage guarantees the working accuracy. The datum choice takes the thick datum by the support big outer annulus end surface, takes the fine datum by the support big outer annulus end surface wit
6、h two craft holes, had determined in its processings craft route and the processing needs each technological parameter. And according to request to a working procedure has carried on based on the hydraulic pressure clamp unit clamp design. Entire processing process chooses all-purpose machine tool.
7、Key words: bracket; processing technic ;special fixture; hydraulic pressure毕业设计说明书论文QQ1961660126目 录摘 要IIIABSTRACTIV目 录V1 绪论11.1 本课题的研究内容和意义11.2 国内外的发展概况11.3 本课题应达到的要求22 支架零件的三维造型33 零件的分析103.1 零件的作用103.2 零件的工艺分析104 工艺规程设计114.1 确定毛坯的制造形式114.2 工艺过程设计所应采取的相应措施114.3 定位基准面的选择114.3.1 粗基准的选择114.3.2 精基准的选择12
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 基于 液压 夹紧 专用 夹具 设计 支架 零件 说明书 图纸